How to install spark plugs 2010 chevy malibu

#How to install spark plugs 2010 chevy malibu manual#
#How to install spark plugs 2010 chevy malibu free#

Label each wire numerically, then give the corresponding plug the same number.

Remember: If you take out more than one spark plug at a time, keep track of your leads and the corresponding plugs by marking them with small pieces of masking tape.

Spark plugs fire in a specific order, and crossing a wire to the wrong plug will make the engine run rough or not at all and can cause damage to your engine. You will need to remove the plugs one at a time, keeping track of the order. If contacts are burnt out, refit the plug and lead to the correct torque setting then go to the auto parts store and get new plugs before removing any more.

When checking to see if the plugs need replacing, simply remove one spark plug and check the gap.

Fit your socket wrench with the extension bar and use the ratchet to remove the spark plug from its housing slowly and with caution. Don't yank on the wire to pull out of the plug, or you've got a bigger job on your hands and a ruined spark plug lead. Pull the wire plug from the engine by gripping it as closely to the bottom as possible and working it gently and carefully off to reveal the spark plug. At this point, it is good practice to inspect the leads for any damage or cracks as replacement leads may also be required. You should also number the corresponding leads to the cylinder so as not to confuse which lead goes where when replacing with new plugs.

#How to install spark plugs 2010 chevy malibu manual#

You should always check your owner's manual and look up where your spark plugs are, how many you have, the correct 'gap' and the size socket needed to remove them. Some cars have engine covers you'll have to remove to see the spark plug wires, tracing them back to find the plugs themselves.On V6 and V8-cylinder engines, plugs should be separated evenly on each side of the engine. On an inline 6-cylinder, they are located on the top or side of the engine head.On a 4-cylinder engine, spark plugs will be located on the top or side of the engine in a row.The spark plugs are located at the engine end of these wires, under the plug covers that attach them. X Expert Source Hovig ManouchekianР В РІР‚СњР В РІР‚С›uto Repair & Design Specialist Expert Interview. When you open the hood or bonnet of your car, you should see a bundle of 4-8 wires leading to different points on the engine compartment. Repeat Steps 2 through 8 on all of the other spark plug wires.Locate the spark plugs in your car. Gently pull back on the boot to test the wire to see if it is locked in place. Place the spark plug wire on the spark plug and turn it half turn in each direction until you hear a click. The spark plug package contains the manufacturer's recommended tension for the spark plug. Remove the socket and test the spark plug tension with the tension tool. Place the new spark plug into the well and turn it clockwise to tighten it. Insert the new spark plug into the socket. No matter what the Chevy Impala model is, apply one or two drops of anti-seize compound inside the wire boot. For newer Chevy Impala models, apply a thin coat of anti-seize compound onto the spark plug threads. If you use the wire brush, gently brush the areas as not to harm any components.Р В РІР‚СњР В РІР‚С›pply one to two drops of clean engine oil onto the new spark plug threads if the Chevy Impala is more than 20 years old.

#How to install spark plugs 2010 chevy malibu free#

Turn the wrench counter-clockwise until the spark plug is free from the spark plug well.Р В РІР‚СњР вЂ™Р’В¬lean the spark plug well and the spark plug boot with a wire brush or canned air. Slide the spark plug socket onto the spark plug. When the lock releases, pull the wire boot to remove the wire.Р В РІР‚СњР вЂ™Р’В¬onnect the extender and the wrench to the socket.

Turn the wire in each direction until the locking mechanism releases. Grab the spark plug wire at the end, or boot, near the engine mount.